Farbacoat Thermofur

Low density pasty product with heat shielding properties. The finished coating creates in a thin dry layer a structure with closed pores filled with rarefied air, the content of which in the volume does not exceed 85%.

Farbacoat THERMOFUR — a pasty product with low density and thermo-shielding properties. The finished coating creates in a thin dry layer a structure with closed pores filled with rarefied air, the content of which in the volume does not exceed 85%.

The product is adapted for use with electric heating systems, pipelines and tanks of various types. Farbacoat THERMOFUR — coating, successfully used in systems of corrosion protection and as an independent coating in marine and industrial environments.

SCOPE OF PRODUCT

pipelines for various purposes;
tank and furnace equipment;
storages and reservoirs;
equipment and machinery;
basements, basements;
furnace equipment;
various technical premises.

PRODUCT SPECIFICATIONS

Appearance	Uniform pasty mass of white color
Duration of drying of the film surface to degree 3 at (20 ± 2) ° С, min., No more than	60
Density, g / cm3	to 0.6
Bending elasticity of the film, mm	1
Adhesion coating, score	1
Resistance to variable temperatures from minus 40 to plus 60 ° С	without changes
The resistance of the coating to the effects of a temperature of +200 ° C in 1.5 hours	no cracks, delaminations, bubbles
Heat conductivity, W / m * K at 20 ° С, not more than	0,068

PRODUCT ADVANTAGES

Eliminates corrosion under insulation.
In anticorrosion systems, the coating is used as a finishing layer that prevents the system from contact with the environment, preventing cracking of the primer layer under the action of alternating loads or vibrations.
High water repellency.
The coating eliminates condensation.
Able to lower surface temperature.
Protects personnel from burns.
Significantly reduces the destructive effect on thermal insulation under a “shock” thermal load (cyclic or rapid temperature difference).
Serves as an additional heat insulating layer without breaks and seams.
Does not put an additional load on equipment, pipelines and machinery, due to low weight.
The coating can be applied in hard-to-reach places, on fittings.

MODE OF APPLICATION

When using Farbacoat THERMOFUR as an independent coating, it is recommended to apply it in 2-3 layers, until the total thickness of 1.5-2.0 mm is reached. It is this coating thickness that is sufficient to effectively lower the temperature of hot surfaces and eliminate condensate phenomena.
If Farbacoat THERMOFUR is used as part of a complex coating, the combined use of the following materials is recommended:
- 1 layer of epoxy coating Farbacoat EPOXI 20 with thickness up to 150 microns;
- 2 layer of thermal shielding coating Farbacoat THERMOFUR from 2 mm;
- 3 layer polyurethane coating Farbacoat URETHAN 30/35 with a thickness up to 50 microns.

The appointment of materials in the system.

Epoxy coating FarbacoatEPOXI 20 is a two-component anticorrosive material that provides reliable anticorrosive protection and adhesion of the ReformIndustrial membrane with the insulated surface.
Thermal shielding coating Farbacoat THERMOFUR is responsible for thermal and thermal insulation properties in the system.
Polyurethane coating Farbacoat URETHAN 30/35 (two-component material) provides the system with decorative (color of choice) properties.

Consumption when applying a thermal shielding coating Farbacoat THERMOFUR without taking into account losses is 1.4 l / sq. m. with a coating thickness of 1 mm.

RECOMMENDATIONS FOR USE

Surface Preparation	Abrasive Blast Cleaning — Sa 2.5 to ISO 8501-1. When repairing the surface, the welds and all damaged areas should be cleaned to the degree of Sa 2.5. After surface treatment, remove dust, abrasive residues and ensure rounding of sharp edges. During long-term storage of primed structures, salt, zinc oxides and other contaminants are removed from the surface before applying the next coating layer. Water jetting to Wa1 grade is used.
Primer	A well-cleaned surface is covered with Farbacout EPOXI 20 or other analogues agreed with the manufacturer.
Application method Airless brush.	Apply in several layers to obtain the required thickness. The thickness is not standardized.
Conditions	air temperature from + 5 ° C relative humidity not more than 85%

The data presented in this technical specification are indicative, theoretical values. Be sure to clarify the data relative to a specific object.

The manufacturer is responsible for compliance with the quality indicators of the materials of the regulatory documentation, but is not responsible for the quality of the installation work and the possible damage caused by the incorrect use of thermo-shielding membranes.

The material is intended for professional use.

STORAGE

It is recommended to store the product in the original packaging for no more than 12 months from the date of manufacture in a dry room, observing the temperature: from + 5 ° C.

NOTE!

Thermal shielding coating Farbacoat THERMOFUR:

non-toxic
chemically inert,
explosion proof,
not combustible,
under normal weather conditions does not emit products harmful and dangerous to the human body,
does not have a harmful effect on the human body even with direct contact.

Референц